PRODUCT DESCRIPTION
Anchor-Set Quick Setting All Purpose Hydraulic Cement. A fast-setting hydraulic cement in dry powder form that, after mixing with water, instantly plugs leaks, above or below grade, stopping flowing water through holes or cracks in masonry.  Anchor-Set anchor bolts, pipes, mailboxes, machinery in just minutes.  Anchor-Set seals and waterproofs, will even set up under water, and is more durable then the masonry to which it is applied.

RECOMMENDED USES
For Surfaces: 
-Concrete     
-Brick        
-Masonry      
-Stone    
- Stucco    
-Metal    
-Plaster   
-Tile
For Patching:   
-Floors/Walls  
-Stairs  
-Landings  
-Curbs  
-Sidewalks  
-Joints  
-Swimming Pools
-Ponds  
-Reservoirs  
-Sludge Tanks   
-Electrical
-Vaults   
-Conduits Holes
-Anchoring:  
-Bolts  
-Security Bars  
-Signs  
-Davits  
-Pool Ladders  
- Mooring Buoys  
-Machinery  
-Seats  
-Posts  
-Racks  
-Mailboxes  
- Railings  
-Pipes  
-Door  Stops

PERFORMANCE INFORMATION:    
-Accelerated Set (3-4 min. initial set)                                 
-Non-Shrinking                         
-High structural strength   
-Sets under
-water
- Easy to use, just add water                                               
- Non-Metallic
- Controlled expansion   
- Non-Toxic when cured
- Seals, waterproofs, fills

SURFACE PREPARATION
General:  All surfaces must be clean and free of dust, dirt, efflorescence, and other foreign matter.  Surface may be cleaned using TSP, or detergent solution. Cracks or holes should be dug out and any old caulking material removed. 
Crumbling, loose and broken material should be removed with wire brush or by chipping.  Cracks or holes should be cut open to a minimum 3⁄4” depth and width, for proper expansion of Anchor-Set. 

Cracks should be cut square, or inner cavity of crack undercut (do not V cut).  If crack or hole is not damp at time or repair, wet the hole with water.  Sweep out all puddles, leaving surface damp but not wet.

MIXING
Use only enough clean water to quickly and thoroughly mix Anchor-Set with a paddle or putty knife to a putty consistency.  Mixing time should not exceed 2 minutes.  Mix only the quantity that can be used in about 3 minutes. 
Mixingwater should be about 70F.  Do not use hot water, because material will set too fast and reduce its strength, unless placed immediately after mixing.  Slower set will result if cold water is used in mixing.  CHECK SETTING TIME
with a small batch.

APPLICATION DATA
Patching and filling cracks:  Place Anchor-Set with force into damp hole or crack by pushing firmly.  Troweling surface may break seal, so smooth surface when placing material.  Hold material in place for one minute.  Keep placed material damp (not wet) for at least 15 minutes.  Shave off excess material with knife.Under water or running water: Place Anchor-Set in crack or hole, starting from side to cut flow.  Force material in with as much pressure as possible.  At
point of greatest flow, hold Anchor-Set in hand or trowel until warmth is felt, then press firmly into opening, maintaining pressure until it sets and leak is stopped. Anchoring bolts, machinery, etc.:  Holes should be drilled deep to secure bolts, and at least 1⁄2” wider on all sides of bolt.  Fill hole with mixed Anchor-Set and immediately force bolt, screw, etc., into filled hole and tamp firmly.  Keep placed material damp (not wet) for at least 15 minutes.  Do not
put pressure on bolt, post etc. for several hours.

COVERAGE
One dry pound of Anchor-Set will fill 17 cubic inches or a crack 3⁄4” X 3⁄4” X 30”.  A 50 pound pail of Anchor-Set will yield 0.45 cubic feet.

CAUTIONS
Contains Portland Cement and Lime.  Product is alkaline on contact with water.  Use putty knife for mixing with.  Always use gloves when working with Anchor-Set.  Avoid splashing into eyes or contact with skin.  In case of skin contact flush with water.  In case of eye contact, flush eyes immediately and repeatedly.  Contact physician immediately.  Wash thoroughly after handling and before smoking or eating.  Do not take internally.PRECAUTIONS:  KEEP CONTAINER TIGHTLY CLOSED.  KEEP OUT OF THE  REACH OF CHILDREN.  CONSULT MATERIAL SAFETY DATA SHEET FOR MORE INFORMATION.

All recommendations, statements, and technical data contained herein are based on tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty either express or implied.  User shall rely on his own information and tests to determine suitability of the product for the intended use and user assumes all risk and liability resulting from his use of the products.  Seller’s and manufacturers sole responsibility shall be to replace that portion of the product of this manufacturer which proves to be defective.  Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product.  Recommendations or statements other than those contained in a written agreement signed by an officer of the manufacturer shall not be binding upon the manufacturer or seller.